ToneShaper Wiring Kit, Stratocaster, HSS2 (Auto-Split)
ToneShaper Wiring Kit, Stratocaster, HSS2 (Auto-Split) Professional Documentation Included Professional Documentation Included

ToneShaper Wiring Kit, Stratocaster, HSS2 (Auto-Split)

SKU
TS-WK-ST-HSS2
In stock
$41.69
-
+

HSS Auto-Split
Most Strats use a middle pickup that is reverse-wound and reverse-polarity (RWRP) so that you get hum-canceling in positions 2 and 4. Add a humbucker into the bridge, and it’s important that you split the humbucker in the 2 position, so that you combine only one of its coils with the middle pickup. This allows you to retain hum-canceling in this position, and it also most-closely approximates the tone of a Strat in the 2 position. You could add a switch of some type that would allow you to manually split the humbucker, but this would mean manipulating two switches. Most players prefer to let the 5-way switch perform this function automatically, so that position 1 is always the bridge humbucker, while position 2 is always the split humbucker combined with the middle.

What about pot values? Humbuckers are voiced with 500kΩ pots (the traditional Gibson value), while Strat pickups are voiced with 250kΩ pots (the traditional Fender value). A 500k volume pot will make the guitar a little brighter, so it’s great with the humbucker, but can make the single coils a little over-bright. Conversely, a 250k pot can make the humbucker a little too dark or “wooly”. With our HSS assemblies you don’t have to compromise. We use a 500k volume pot so that the humbucker sounds right in position 1, but we add a resistor into the circuit in the other 4 positions, dropping the load to 250k, so that the other positions sound right. Hey, who wants to compromise where tone is concerned?

Finally, to make this wiring truly custom, we’ve used our ToneShaper narrow superswitch rather than the standard 5-way, so that we can customize the tone controls. The standard Strat switch assigns the tone controls to specific pickups, but the superswitch assigns them to specific switch positions, which allows for more granular control. We’ve assigned the lower tone control to position 1 only, and we’ve used Gibson-esque values for both the pot and the tone capacitor. This optimizes the tone controls for their respective positions: Gibson values for the “Gibson” position (1), and Fender values for the “Fender” positions (2/3/4/5).

This kit
includes everything you need to wire an HSS Stratocaster with auto-split humbucker (refer to the images above for a switching diagram). This is our most popular wiring scheme for HSS Strats. It includes the finest components, from the same suppliers that the large U.S. guitar companies have used for decades:

• (1) Capacitor, .022µF Orange Drop
• (1) Capacitor, .047µF Orange Drop
• (1) Jack, Switchcraft 1/4" Mono
• (1) Pot, CTS 250k Audio, Low Torque (1/4" Bushing Length)
• (2) Pot, CTS 500k Audio, Low Torque (1/4" Bushing Length)
• (1) Resistor, 470k
• (1) Screw for Shielding Ground Lug
• (1) Shielding Ground Lug
• (1) Switch, 5-Way, Oak-Grigsby, 4-Pole Superswitch
• (1) Treble Bleed Kit for Single-Coils
• (3) Wire, 22 AWG Cotton Push Back w/ Tinned Overcoat, Black
• (3) Wire, 22 AWG Cotton Push Back w/ Tinned Overcoat, White
• (3) Wire, 22 AWG Stranded Silver-Plated Copper, Black PTFE
• (3) Wire, 22 AWG Stranded Silver-Plated Copper, White PTFE
• (1) Professional, Fully-Illustrated Wiring Diagram

More Information
Enable Recurring Profile No
UPC 852606002533
Guitar Type Stratocaster
Pickup Configuration (HSS) HB|SGL|SGL
Apply MAP No
Write Your Own Review
You're reviewing:ToneShaper Wiring Kit, Stratocaster, HSS2 (Auto-Split)
Your Rating